Emerald Spa Parts & Accessories

2" x 15" Heater, complete. 240 Volt, 5.5 Kw used in 'SS' and 'DS' control systems. Pressure switch installed and calibrated, includes unions w/ gaskets. Ships direct from Emerald Spa, please allow 7-10 days for delivery.

Emerald Spa 'Gecko Pack Heater' 2' X 15" tube with NEW flexible bulkhead contacts (no nuts to attach!) New smaller style pressure switch installed and calibrated. For all Emeralds with blue plastic spa pack, M or S Systems. 4 kW, 240V. Includes union nuts. Ships directly from Emerald Spa corp, please allow 7-10 days for delivery.

Emerald Heater for Emerald Spas used 1991-93, 1.5 inch unions X 16 inches length, 6kW, 240V, non-replaceable element.

20" long, 5" diameter, 2 1/8" hole at both ends. Codes: Unicel #C4975, Pleatco #PRB75, Filbur #FC2395, Emerald #40029100 Fits: Emerald Cygnus, Hydro Pool, Serenity, CMP, Dakota.

17" long, 2 7/8" diameter. One filter has 1" hole. One filter has 2 1/8" hole. blue filters (top) are new 'microban' version. Codes: Unicel=2302, 2303, Pleatco=N/A, Filbur=2320, 2324 Fits: Emerald Spas, Rainbow 'space-saverII' & others.

‘MAGNA’ series jets. (SHOWN ABOVE - COMPLETE JET, WHITE, DIRECTIONAL $42.00)

Adjust jet pressure by turning handle. Requires a 2 5/8 inch hole size. There are 5 JET BODY (CLEAR) styles available, chosen by air and water supply line sizes. A jet body includes wall fitting and gasket (#1), and nozzle assembly (#8) which are all available seperately below. #7 in picture is OLD two piece nozzle that is no longer available, replaced by NEW one piece unit shown #8.

COMPLETE JET is available in 1 inch air and 1 ½ inch water sizes only. Choose between directional style jet or dual-port spinner jet. The three inner JET styles, available in white or grey, are SINGLE PORT SPINNER (#3), DIRECTIONAL EYEBALL (#4), and DUAL PORT SPINNER (#5). These will snap into the HANDLE (#2 white or grey) that slides onto nozzle inside body and snaps into wall fitting. Removed by prying/popping out. There is also a stainless trim ring (escutcheon) that presses on handle (#6) There is a WRENCH for wall fitting (not shown) also found below.

It's Back! This is Hydro-Air Brand VSR Adjustable Jet, 2010 retrofit version available now! Smooth grey face only, 5 inch face diameter, 4 5/8 inch standing height. Inner nozzle moves to adjust spinning radius. fits all previous bodies (still available) with new lockring, shown center.

This newer style is more durable, and no 'tabs' to erode, break off. To install: (1) drain spa. (2) clean inside existing jet body thoroughly (3) apply pvc cement [no primer] inside body fully encircling inner radius at 1.5 inch depth only[blue area] as well as outer surface of lock ring (4) insert lock ring and seat fully into jet body, making sure to align tab to slot [red] - wipe off excess cement immediately. (5) After glue dries [30 min] insert jet into body, aligning green tab(shown bottom right backside of jet) to green slot along body and press to snap in.

Hole size is 3 ½ inch, size shown is ¾ water and 3/8 air barbed body. (most typical- email us for other configurations) Two bodies shown, with jets(shown for reference), body inludes nut and alignment ring, no gasket. Body protrudes 4 ½ inches behind tub wall, needs 4 ½ inch flat area to mount. To install use 100% silicone on tub side. NOTE:these JETS are now avail again for 2010!

Pentair brand cyclone luxury jet for Emerald Spas. 3 3/4" diameter across face, 3 15/16 inches standing height. grey only, 5 scallop adjustable pressure. Removed by rotating fully clockwise and prying/popping out. Install by lining up 2 tabs to slots in jet body and clicking in.

LEFT: CYCLONE LUXURY EYEBALL ($16.)directional internal. MIDDLE: Cyclone internal backside shown for reference purpose. RIGHT: CYCLONE LUXURY SWIRL ($18.)directional rotational internal. Inquire for stainless smooth face.

Pentair Brand Cyclone Euro Jet internal for Emerald Spas. 2 1/8" diameter across face, grey 5 scallop only. Removed by rotating fully clockwise and prying/popping out. Install by lining up 2 tabs to slots in jet body and click in.

Pentair cyclone swirl jet. Adjustable directional rotational internal. Emerald logo on scalloped face. 5 1/4" diameter across face, grey 5 scallop only. Removed by turning fully clockwise and prying/popping out. Install by lining up 2 tabs to slots in jet body and click in. Typical failure results in bearing ejection from acidic pH/old age/sanitizer damage.

Hydro-Air brand 'Duo' Swirl jet for Emerald Spas. The smallest spinner jet, 1 5/8" across face with two locking tabs on wall fitting that twist lock into two channels in faceplate. TIP: silicone these babies on there, keep pH locked in.

GG Industries suction intake for Emerald Spas. For 2" PVC, 4 post style, removable cover.LEFT: SUCTION WALL FITTING $6.00 RIGHT: SUCTION COVER white only,$12.00,100GPM

Hydro-Air flexible neck jet assembly for Emerald Spas. Complete snap-in jet shown on left. Wall ftg.and jet body shown on right included as well, sold as a complete unit only in white. Replaces grey uncovered flexible style.

Emerald Spa air injector, complete (front) dark grey only, for 3/8" clear vinyl tubing. This is the one and only -Jan '09 version...replaces ALL older styles -white round one, grey scalloped 'flower' style, and '08 shalt-shaker type. TIP: Clean spa shell thoroughly,silicone everywhere, don't over-tighten (21 in.-lbs. max),Use pvc glue to affix in cleaned tubing (no primer), no "hose hang" from backside.

LEFT: GG Industries brand air control for Emerald Spas for 1" PVC, grey only, complete. RIGHT: Pentair brand air control for Emerald Spas for 1" PVC, grey only, complete. BOTH: require cutting/gluing PVC to install. NOTE: I.D. tags on Pentair model pop out and are re-useable.

Hose drain/valve for Emerald Spas -2009 version. Cabinet or toe-kick mounted drain unit, complete, with cap. 3/4" barb end. Mounting flange (large plastic disk- not shown) is typically re-used if on your model. Barb attachment on LEFT can be glued in for inside slip on clear lines, or 1/2 inch flex pvc will glue inside valve. To open, turn counter-clockwise and PULL OUT to open fully, reverse to seal.

(#1) CAP COVER (#2) THREADED FILTER CAP, CAP O-RING (not shown)(#3) Filter cap key/light lens tool

Pentair/Rainbow chlorine/bromine dispensers for Emerald Spas. LEFT: Complete dispenser for 1" chlorine or bromine tablets. Used in 25, 50 and 75 square foot filter canisters. Includes O-rings, bottom check valve cap, bleeder valve. O-ring for cap (shown installed - large) RIGHT: Complete dispenser for "Space-saver II" filter system. For 1" chlorine/bromine tablets. Includes O-rings, check valve cap. O-ring for cap (shown installed) MIDDLE: Check valve assembly, complete w/ o-ring, fits both dispensers.

Waterway skimmer door for use in all Emerald spas. Includes foam float block (two shown for reference) door is 4 3/4" tall and 5 1/16" wide.

Pentair/Rainbow Space-Saver II filter housing. Comes complete as shown, 2 inch in/out glue fittings, includes dispenser unit and cap. Mounts from UNDER spa shell and requires possible extensions of supply and discharge lines after old unit is cut out. For dispenser or it's parts see the Emerald parts page.

Emerald Spa pillow, suction cup style. Measures 9 1/2 X 6 X 3 inches. Black only with Emerald logo.

Hydro-Air 5 inch suction fitting. VGB COMPLIANT. Rated at 208 GPM, 4 inch hole size needed, 2 inch slip glue connection, white, Includes: Nut, alignment collar, wall fitting, suction cover.

For use in Emerald Spas. 5 1/4 inch face, 3 5/8 hole size needed. Shallow backside of jet internal clicks into body at green colored slot. Sold complete as: jet, body, alignment ring, gasket and nut. parts sold separate below. Grey 5-scallop face only.

Aqua-Flo XP2 48 frame pump head. 2 inch intake (center) and discharge. Available as complete wet end for. This includes front and back halves of pump volute,O-ring, stainless bolts, seal, impeller, wear ring,and drain plug. Very similiar in design to Waterway brand 'executive' pump, note less ribs on faceplate on XP2.

Or order individual parts: LEFT: Pump Union w/ o-ring for 2" PVC RIGHT: Impellers - need to specify horsepower of motor: choose - 1.5, 2, 2.5, or 3 (NOTE: This is all that's made for XP2, if your motor says more than 3 then use 3 HP impeller) BOTTOM CENTER: Seal Assembly, complete, for all BELOW PUMP: Drain Plug w/ O-ring NOT PICTURED: O-ring for pump halves NOT PICTURED: Wear Ring for impeller, white, fits all.

Includes overlay sticker and self-adhesive tape to apply to tub shell. Plugs into circuit board with phone-jack style plug.

Includes overlay sticker and applies using self-adhesive tape. Plugs into circuit board with phone-jack style plug.

For MC2 and MC4 systems. Includes overlay sticker and uses self-adhesive tape to apply to tub shell. Plugs into circuit board with pin connector plug.

Includes overlay sticker and self-adhesive tape to apply to tub shell. Plugs into circuit board with pin connector plug.

Includes overlay sticker. Plugs into circuit board with pin connector plug. Adhesive self-stick tape applies to tub shell.

Emerald Spa topside control DS2. Balboa brand 6 button controller for all 'DS2' systems. CAT 5 style plug with high quality self-adhesion tape (if NOT included use 100% silicone). Faceplate sticker included.

Balboa 8-button topside control for Cygnus Spas. For all Cygnus series Emerald Spas, 'DS4' systems. (may also work in conjunction w/remote control PS51602). CAT-5 cord end, may have self-adhesive tape on back, if not use 100% silicone. overlay sticker is included.

Balboa Lite Leader topside control for Emerald Spas. For all "SSOD and SS1D" systems. 2 button basic controller for small spas, phone plug style cord, complete w/ overlay sticker. May have self-adhesive tape on back, if not use 100% silicone.

Emerald Spa Topside Controller SS3D Balboa brand 4 button controller for all 'SS3D' systems. CAT 5 style plug. High-quality adhesion tape (If not included use 100% silicone)and faceplate sticker included.

Emerald Spa CYGNUS remote topside control. Balboa brand jet/blower actuate buttons for Cygnus series spas. Phone-style jack cord, faceplate sticker and high-quality self-adhesion tape included. may or may not have Emerald logo on sticker.