 | Low flow canister measures 3 inches diameter, 6.5 inches long, 3/4 inch barb end connections. 240Volt, 4.0kW. Thermcore Brand, 1 yr warranty. Black housing shields pressure switch (installed & calibrated) and heater contacts. Specific cord ends should identify this common heater. $295.00 |
|
 | Replaces JWB# 6521000, 240Volt, 5.5kW,2 1/4 inch slip ends for couplings, 17 3/8 long. The standard heater for decades for numerous Jacuzzi models. Recently available with replaceable element (not shown). Note picture showing large nut under connection terminals identifying a replaceable element unit. Prior heaters from the 80's-2009 DO NOT have replaceable elements.Two thermowells for sensors, hi-limit included and installed. $255.00 |
|
 | 4kW, 240Volt. Used in R574 and R576 systems. $198.00 |
|
 | 5.5 kW, 240Volt. Includes foam wrap. ¾ inch in/out. $248.00 |
|
 | Compression fittings for 1/4 inch outside diameter white hard lines. Used on Jacuzzi's for years for primer lines and drainback feeds. Available in straight and 90 degree style. 1/8 inch npt threads - install w/ teflon tape or 100% silicone. Includes complete fitting: body, nut, compression gasket and stainless pinch ring. $11.00 |
|
 | Jacuzzi Brand air controls. Most common valve used for decades. Notice NEW style spring loaded valve internal (red). Old style (purple) shown for reference. SOLD AS INDIVIDUAL PARTS: TWO-KNOB FACEPLATE, almond color. Mounting screws are stainless, and typically re-used or available locally. $24.00 |
|
 | COMPLETE JET (white only - save $5!) Includes body w/ alignment ring and nut, nozzle, clamping ring and gasket. Stainless bolts are common #8-32x1/2 inch. Older bodies will have screws that bite into plastic, newer has brass threaded inserts and use stainless bolts. $80.00 |
|
 | Jacuzzi 'BMH' jet, complete. Available in grey/silver only (shown on right), as a complete unit, including jet body nut (not pictured). Hole size needed is 2 inches, jet body has one inch water and air slip glue ftgs. $52.00 |
|
 | COMPLETE JET (save $15.00) includes one each of JET BODY 1 1/2 inch water slip glue ftg. and 1/2 inch air. Hole size needed is 3 1/2 inch, PVC PLUG, ALIGNMENT RING, LOCK NUT, SWIVEL ASSEMBLY, 3-HOLE PLASTIC CLAMP RING w/ LOGO, 3-HOLE CLAMP RING GASKET. Use Stainless #6 screws, 1/2 inch long to clamp in swivel assembly to allow limited movement for adjustability. There are no gaskets for tub side, make sure to use 100% silicone. $106.00 |
|
 | Sold complete or separate parts available below. Hole size needed is 4.5 inches. For 1.5 inch pvc supply, 1/2 inch air supply. Swivel assembly sold complete less handle (at right if card). Body includes alignment ring and nut. $140.00 |
|
 | Jacuzzi brand pump union. Fits many Jacuzzi-only pumps, thread-specific. fits 1 1/2 inch (inner) or 2 inch (outer) PVC pipe. Proprietary 'knuckle' design permits swivel movement of pipe inside threaded nut. One set includes nut, body, and O-ring. $11.00 |
|
 | Jacuzzi air bellows. Topside mounted air button used in Jacuzzi Brand tubs for decades. Used to actuate rocker air switches for function selectors, and attaches to clear airline tubing. Comes complete with silver trim only, ONE bellows. $48.00 |
|
 | Jacuzzi thermostat knob. Silver/grey only.Used on older (70's,80's,90's) control systems, attached to flexible control cable (ask us..) and slips over flat-sided round shaft. $12.00 |
|
 | Jacuzzi air button repair kit. Used to replace buttons and trim on Jacuzzi bellows. Set of two (as shown), Silver/grey only. $42.00 |
|
 | Jacuzzi Whirlpool Bath pump. Complete with grey flange and two 4-bolt unions and gaskets. This is a non-rebuildable pump, sold as a complete unit. There are tens of thousands of these out there, made for a few decades. There is only one that looks like this. If you have a seal leak then you need to replace entire pump. $354.00 |
|
 | Jacuzzi J, K, style pump head COMPLETE. Special order. This version accepts Jacuzzi's 'self-aligning' 1 1/2 inch pump unions. (Contact us for standard thread pump union version). $198.00 |
|
 | Jacuzzi Piranha pump head. 48 Frame, 2 inch standard pump unions, complete. Special order. NOTE:***6/1/12*** FRONT half of pump is no longer available! glue up what you have, or switch out complete wet end. Sorry folks! $160.00 |
|
 | Jacuzzi Brand skimmer door. Found on Jacuzzi's for decades, as well as many other brands. Press/snap fits on skimmer box, sold as one-piece unit, parts not avail separately. Comes in silver/grey only. $108.00 |
|
 | Jacuzzi skimmer tray. There's only one, this is it... slides in shelf tabs inside Jacuzzi Brand front-load skimmer boxes, behind two-part hinged door. (see: Jacuzzi skimmer door) Measure 7 1/2 inches X 6 3/8 inches. $18.50 |
|
 | Jacuzzi 50 sq. ft. filter for Aero, Caressa, etc. using skimmer box with weir door (two part folding door). Measures 5 5/8 dimeter, 10 3/8 long, closed top, and 2 1/8 inch hole on bottom. Note pull string to remove from skimmer. Codes: Unicel = C-5300, Filbur = FC1320, Pleatco = PJW50. $38.00 |
|
 | Jacuzzi 25 sq. ft filter for Aero, Caressa, etc using skimmer box with weir door (two-part folding door). Measures 5 5/8 inch diameter, 10 3/8 inches long, closed top and 2 1/8 inch hole on bottom. Note pull string to remove from skimmer. Codes: Unicel = C-5601, Filbur = FC-1330, Pleatco = PJW23. $26.00 |
|
 | $48.00 |
|
 | Jacuzzi 25 Spa Filter for Jacuzzi, Seven Seas Apollo Spas and others. |
|
 | $35.00 |
|